If a data format is found for a particular symbol, those prefixes and suffixes are not transmitted. Any data that does not match your data format requirements generates an error tone. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the bar codes below. Page For example, you may have set your device to the data format you saved as Data Format 3.
Page 6 - Page Symbologies This programming section contains the following menu selections. Refer to Chapter 11 for settings and defaults. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology. Refer to Message Length Description page for additional information.
Page Code 39 Message Length When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Page Code 32 Pharmaceutical Paraf which the bar codes are read, deleting the first space from each. The scanner transmits the appended data when it reads a Code 39 bar code that starts with a character other than a space. Page Interleaved 2 Of 5 and scan the value and the Save bar code from the Programming Chart the inside the back cover of this manual.
The data characters should then appear properly. Page Interleaved 2 Of 5 Message Length When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Page Code Code Page that supports concatenation of neighboring symbols, and 4 the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off.
When turned off, there is no space. If you need to read codes that lead with the 1 number system, use UPC-E1 page To prevent transmission, scan Off. For these codes, use UPC-E0 page When turned Off, there is no space. You can program the scanner to read MSI bar codes with Type 10 check charac- ters. Trioptic Code is used for labeling magnetic storage media. GS1 Composite symbologies allow for the co-existence of symbologies already in use. Any applica- tion that accepts GS1 data can be simplified since it only needs to recognize one data carrier type.
If GS Emulation is scanned, all retail codes U. All bar code readers are capable of reading the Code 39 linear component.
Only one 2D postal code selection can be active at a time. If you scan a second 2D postal code selection, the first selection is over- written. Page Chapter 8 - Imaging Commands Imaging Commands The scanner is like a digital camera in the way it captures, manipulates, and transfers images.
The following commands allow you to alter the way the scan- ner performs these functions. Single-Use Basis Imaging Commands with their modifiers send instructions to the scanner on a single-use basis, and take effect for a single image capture. The image snap command has many different modifiers that can be used to change the look of the image in memory.
This is similar to setting a shutter speed on a camera. The exposure time determines how long the scanner takes to record an image. On a bright day, exposure times can be very short because plenty of light is available to help record an image.
Page W - Target White Value Sets the target for the median grayscale value in the captured image. For capturing close-up images of high contrast documents, a lower setting, such as 75, is recommended. Higher settings result in longer exposure times and brighter images, but if the setting is too high, the image may be overexposed. The last image is always stored in memory. The image ship commands have many different modifiers that can be used to change the look of the image output.
Page C - Compensation Flattens the image to account for variations in illumination across the image.
Page E - Edge Sharpen An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen filter can be entered from 1 to Page H - Histogram Stretch Increases the contrast of the transmitted image.
Not available with some image formats. Higher numbers result in higher quality, but larger files. Smaller numbers result in greater amounts of lossy compression, faster transmission times, lower quality, but smaller files. Range: - Page V - Blur Image Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image.
This software is available at www. Click on Soft- ware Downloads. Below is an example of a signature capture application. In this example, the aimer is centered over the signature capture area and the trigger is pressed. Page This option is used to size the image horizontally. If using this option, set the resolution R to zero. Page For example, use to specify a resolution of 2.
Negative numbers indicate that the signature cap- ture is above the bar code, and positive numbers indicate that the area is below the bar code. Page 8 - The following chart indicates the equivalents of these five characters for different countries. Page 9 - See the Symbology Chart, beginning on page A-1 for the single character code that identifies each symbology.
This action first clears all current prefixes, then programs a Code I. Data Format Settings Test Menu When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a programming code. The pro- gramming function will still occur, but in addition, the content of that program- ming code is output to the terminal. Apps are stored in groups: Imaging, Decoding, and Formatting.
NET software. Access the Honeywell web site at www. Click on the Resources tab. Select Product Downloads-Software. Page 7. Double click on the Setup. Follow the screen prompts to install the EZConfig program. Page 10 - Page Conventions Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will pro- gram the scanner. For complete descriptions and examples of each serial pro- gramming command, refer to the corresponding programming bar code in this manual.
Page Query Commands Storage A single character that specifies the storage table to which the command is applied. An exclamation point! A period. Page Responses Responses The device responds to serial commands with one of three responses: ACK Indicates a good command which has been processed.
Page Standard Cable Pinouts 12 - Page 12 - These ser- vices are to be performed only by an authorized service center see Customer Support on page Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following periodic checks ensure dependable operation: Cleaning the Device Replacing an Interface Cable 1.
Turn the power to the host system OFF. Page Changing A Scanner Battery and press firmly. If the ID is rejected it means the customer is not old enough to purchase any items that are out of his or her age level. They will also be unable to purchase anything else in the transaction that they do not qualify for. In order to reset the invoice back to normal please press void. Search for:. Remove Custom Defaults 2. Post navigation Whirlpool Microwave Manual Download. Carriage Return simulates Enter key - Use this if when you scan a barcode, you have to press enter to get the item onto the invoice grid.
This code works best if you print out the code. Step 2: You can modify up to 3 age levels for your items. The most common ages are 18, 19, and When you are done entering in the age levels click Update.
Step 4 : Check the box for the ID level you would like to set. Check ID 3 will be set to Click Update and Exit. Step 5: Ring up the item as normal, a new box will appear for an ID scan.
0コメント